Harman-kardon DVD47 User Manual download pdf (Page 29)

DVD PLAYBACK

PLAYBACK INFO Submenu: This submenu

displays basic disc and playback mode information

(see Figure 12). You may not make any changes to

the items shown in this submenu, except for the

Repeat mode.

■ Disc: This line displays the disc type, such as

DVD-Video.

■ Disc ID: If the disc is encoded with an identifica-

tion label, such as a movie title, it will appear here.

■ Playlist: For DVDs, this line will reflect that play-

back will occur in the disc’s order. Programmable

playlists are not available when a DVD is loaded.

■ Repeat: This line displays the current repeat

mode, or Off if Repeat mode is not active.

Figure 13

PROGRAM submenu: The PROGRAM sub-

menu is not accessible for DVDs.

DISC INFO Submenu: This submenu displays

detailed information about the disc content (see Figure

13). You will not be able to make any changes to the

items on this submenu. However, you may use the

Setup menu system as described on page 23 to

change the DVD 47 player settings for video aspect

ratio or scan type.

■ Disc: This line displays the disc type.

■ Disc ID: If the disc is encoded with an identifica-

tion label, it will appear here.

■ Aspect Ratio: This line displays the aspect ratio

of the video content on the disc, and the format in

which it is being played back according to the set-

ting established in the VIDEO SETUP sub-

menu as shown on page 23. Some discs may

contain two versions of the same program with a

widescreen aspect ratio on one side of the disc,

and a standard aspect ratio on the other.

■ Video Standard: The disc’s format is shown

here. For Region 1 players, this will normally be

NTSC, although some DVDs that are open region

(playable in all regions) may be in the PAL format.

The DVD 47 will convert the video to the NTSC

format used by your television.

■ Scan Type: This line displays whether the video

program on the DVD was recorded with a pro-

gressive or interlaced scan rate. It also displays

how the program is being played back, based

on the setting established in the VIDEO

SETUP submenu as shown on page 23.

■ Audio Resolution: This line displays the sample

rate and bit rate for the current audio format.

■ Audio Format: This line displays the current audio

track, such as Dolby Digital 5.1 or linear PCM.

■ Video Bit Rate: This line displays the video bit

rate up to the limit of 10 Mbps. This indication will

vary as a disc is played in response to changes in

the amount of compression that was applied to the

video signal when the disc was created. Thus, as

shown in Figure 13, when the disc is stopped or

paused, this line will remain blank.

When you have finished viewing the Player menus,

press the Info Button i to remove the displays

from the screen and return to normal play.

Using the On-Screen Status Display

When a DVD is playing, you may press the Status

Button  at any time to view a quick summary of

the disc’s playback status. The Status Bar not only

gives you a snapshot of the unit’s current state; it also

provides an easy way to select a different group, title,

chapter or track, or use the time search feature.

Figure 14

• Group/Title

: For DVD-Video discs, this dis-

plays the current title on the left, and the total num-

ber of titles on the disc on the right. For DVD-Audio

discs, the number of current and total groups is

shown.

• Chapter

: For DVD-Video discs, this shows the

current chapter on the left, and the total number of

chapters on the disc on the right. For DVD-Audio

discs, the number of current and total tracks is shown.

• Play Mode Icon

: This displays the current

play mode icon: e.g. Play ›, Pause ±, Stop

Í.

• Time Display

: This section of the display

shows the time corresponding to the type of display

indicated in the Time Display Type

. The Time

Search function enables you to start playback at any

point in the program. Use the ‹›Navigation

Buttons D to highlight this display, and the num-

bers will change to dashes. You may then use the

Numeric Keys  to enter the numbers corre-

sponding to the time on the disc at which you wish

play to commence. Press the Enter Button t,

and play will immediately begin at the selected

time position.

• Time Bar : This display is a graphic represen-

tation of the time elapsed for the title being played.

As the disc plays, the number of bars will increase to

reflect approximately what percentage of the title has

been played thus far.

• Time Display Type

: This section identifies the

type of information in the Time Display

sec-

tion of the display. Use the

⁄¤‹› Navigation

Buttons D to select this setting, and each

subsequent press of the Enter Button J will

change the time display from Title Elapsed, to

Title Remaining, to Chapter Elapsed to Chapter

Remaining, and cycle back to Title Elapsed. The time

displayed on screen and in the front-panel

Information Display @ will change accordingly.

For DVD-Audio discs, the time display options are

Group Elapsed, Group Remaining, Track Elapsed and

Track Remaining.

Selecting a Title or Group

To select a title or group, first press the Status Button

 so that the Status Display appears. The Current

Title or Group

will be highlighted in a blue box.

Press the Enter Button J and dashes will appear,

enabling you to use the Numeric Keys  to enter

the desired title. Press the Enter Button J again to

begin playing the new title or group. Note that if a “ø”

icon appears when you attempt to select a new title

(group), this is an indication that the disc does not

allow the title (group) to be changed in this manner,

even though a list of numbers will appear. This is a

function of the way the disc was created and is not a

flaw in the DVD 47. For some discs, press the Title

Button  during playback to change the current

title or group. Some discs will switch to the disc menu,

and some discs may simply restart play from the

beginning of the current title or group. This is a func-

tion of how the disc was authored, and does not

reflect a problem with the DVD 47.

Selecting a Chapter or Track

To select a chapter for DVD-Video discs or a track for

DVD-Audio discs, first press the Status Button Q

so that the Status Display appears. Next, press the ›

Navigation Button D so that the Current Chapter

or Track Number

is highlighted and dashes

appear. Use the Numeric Keys  to enter the

desired chapter or track, and press the Enter Button

J to begin playing the new chapter (track).

To select a specific chapter or track on a DVD at any

time during playback, simply press the number corre-

sponding to the chapter or track you wish to view

using the Numeric Keys . You may also move

one by one through the chapters or tracks at any time

by pressing the Skip Reverse (Previous)/Skip

Forward (Next) Buttons 56AP.

E F G

DVD PLAYBACK 29

1 2 ... 24 25 26 27 28 29 30 31 32 33 34 ... 39 40

Comments to this Manuals

No comments

Harman-kardon DVD47 User Manual Page 29

Comments to this Manuals

Related products and manuals for Receivers and Amplifiers Harman-kardon DVD47