Harman/Kardon HS210 User's Guide download pdf (Page 18)

18 19

= Learning-Capable

Teaching Codes to the Remote Control

Place the 1. HS 280/HS 210 remote head to head with the remote from which

you want it to learn codes. Put them about 1 inch (2.5cm) apart, with their IR

transmitter windows facing each other.

Press and hold either the TV or Video button on the 2. HS 280/HS 210 remote.

Learn Button

TV Button

Video Button

Learn Button

TV Button

Video Button

While pressing the TV or Video button, press and hold the Learn button until its 3.

LED begins flashing amber. (The TV or Video button will not flash but will remain

steadily illuminated.) The flashing indicates that the remote is in the learning

mode.

Press the 4. HS 280/HS 210 remote button to which you want to teach the

command. The Learn button’s LED will then illuminate continuously. The learning

mode will remain active for 20 seconds after the button is pushed.

NOTE: If you accidentally press a button that is not learning-capable, the Learn

button's LED will continue to flash amber and the remote will remain in the learning

mode.

Press the button on the other remote that you want to “teach” the 5. HS 280/HS 210

remote. When the HS 280/HS 210 remote has received and stored the other

remote's IR code, the Learn button’s LED will change to green, and the HS 280/

HS 210 remote will remain in the learning mode, ready to learn another code.

NOTE: If the HS 280/HS 210 remote can’t read the IR code from the other remote,

the Learn button’s LED will flash red rapidly three times, and the remote will remain

in the learning mode. Resume programming from Step 4. If the HS 280/HS 210’s

remote control does not receive an IR code within five seconds, the Learn button's LED

will flash red rapidly three times, and the remote will remain in the learning mode.

Resume programming from Step 4.

Repeat 6. Step 3 and Step 4 for each command you want to teach the HS 280/HS 210

remote. You can switch between programming TV and video component codes

by pressing the TV or Video button before resuming Step 4. NOTE: If the Learn

button’s LED goes out at any time, you will need to repeat Step 2 through Step 6.

Using the Remote Control After it is Programmed

Pressing the remote’s TV button will put the remote into the TV-control mode. It will

control the TV via the codes you have programmed into it. Pressing the remote’s Video

button will put the remote into the video-control mode, and it will control the video

component via the codes you have programmed into it.

To switch the remote control back to the HS 280/HS 210 receiver-control mode from

the TV-control or video-control mode, press any of these buttons: Disc, Radio, USB,

Network, Activity or Bookmark.

Setting up the Receiver

NOTE: The on-screen menus shown in this manual are for illustrative purposes and

may differ slightly from the actual displays.

Using the On-Screen Menu System

When you turn your HS 280/HS 210 receiver on for the first time, the on-screen menu

will display the Activity menu. This menu acts as the HS 280/HS 210’s “home” screen.

All of the HS 280/HS 210’s on-screen functions originate in the Activity menu.

To operate your HS 280/HS 210 system, you will use the remote control to navigate

through all of the on-screen menus and make selections from them.

Cursor Buttons

Enter Button

Cursor Buttons

= Learning-Capable

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 29 30

Comments to this Manuals

No comments

Harman/Kardon HS210 User's Guide Page 18

Comments to this Manuals

Related products and manuals for Home cinema systems Harman/Kardon HS210