Harman/Kardon HS210 User's Guide Page 14
- Page / 30
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
14
14 15
Connections
CAUTION: Before connecting anything to the HS 280/HS 210, ensure that the
HS 280/HS 210 receiver is turned Off and the receiver’s AC cord is unplugged
from the receiver and the AC outlet.
Connecting the Satellite Speakers
Speakers and receivers/amplifiers have corresponding ( + ) and ( – ) connection
terminals.
Your system’s
•
SAT TS60 left and right speakers use red to denote the ( + )
terminal and black for the ( – ) terminal.
The
•
HS 280/HS 210 receiver uses white to denote the left channel ( + ) terminal
and red for the right channel ( + ) terminal.
Black
•
is used to denote the ( – ) terminal of both channels.
The speaker wires included with your system have colored bands at both ends of
the ( + ) conductor; the colors correspond to the receiver’s ( + ) terminal colors. The
subwoofer cable has purple connectors that correspond to the color of the receiver’s
subwoofer output and the color of the HKTS200SUB subwoofer’s LFE jack. This system
helps you connect each speaker to the correct receiver or amplifier terminals. In
addition to the colored bands at each end, each speaker wire’s ( + ) terminal has ribs
molded into its insulation to help you identify it.
For the speaker-connection instructions on pages 6 through 9, thread the appropriate
speaker cable through the opening in the bottom of the attachment plate and then
through the back of the bracket, as shown in the diagram.
Wires to Speaker
Terminal Cover
Overhead View
Wire
From
Wall
Plate
The bracket has two openings on top: a round
screw hole and an arc-shaped opening in front of
it. Thread the speaker cable through the arc-
shaped opening, not the screw hole.
Attach the bracket to the wall plate by inserting
the tab at the top of the attachment plate into
the slot on top of the bracket and snapping the
bracket onto the attachment plate.
Thread the cable through the round opening in the terminal cover. Insert the speaker
wires into the terminals on the underside of the speaker, remembering to observe the
correct polarity (see “Speaker Connections”).
Place the terminal cover over the opening on the underside of the speaker so that
it fits flush against the speaker and covers the terminals, with its round opening
exposing the threaded insert. The bracket fits through the round opening in the
terminal cover.
Wall Bracket
Insert the supplied bracket bolt up through the
bottom of the bracket and terminal cover. Screw it
into the threaded insert on the underside of the
speaker. The bolt should be snug, but not so tight
as to prevent the bracket from pivoting.
The wall-mounted speaker may be pivoted from side to side; however, the bracket is
not designed to tilt up or down, and attempting to tilt it will damage the bracket and
possibly the wall. Your warranty will not cover the damage.
Wall
(M6-1.25P
or 1.4"-20)
23 mm
It is very important to connect each speaker identically: ( + ) on the speaker
to ( + ) on the receiver or amplifier, and ( – ) on the speaker to ( – ) on the
receiver or amplifier. Miswiring one or more speakers results in thin sound, weak
bass and a poor stereo image.
To connect the speaker wire to the terminals on the satellite speakers:
Press down on the top of the terminal to open the connection hole.1.
Insert the wire’s bare end all the way into the hole. Insert the conductor with the 2.
colored band into the speaker’s red ( + ) terminal, and insert the other conductor
into the speaker’s black ( – ) terminal.
Release the terminal to secure the wire to the terminals.3.
A. Push Down on Cap
to Open Hole
B. Insert Base Wire into
Open Hole
C. Release Cap to Secure
Wire
+
–
IMPORTANT: Make sure the ( + ) and ( – ) bare wires do not touch each other or the
other terminal. Touching wires can cause a short circuit that can damage the receiver.
To connect the speaker wire to the terminals on the receiver:
Unscrew the connector sleeve to expose the hole in the connector post. 1.
CAUTION: Take care not to unscrew the sleeve completely off the post.
Insert the wire’s bare end through the hole in the post. Insert the conductor with 2.
the red colored band into the receiver’s red ( + ) terminal. Insert the conductor
with the white colored band into the receiver’s white ( + ) terminal. Insert the
unmarked conductors into the receiver’s black ( – ) terminals.
Tighten the connector sleeve to secure the wire. 3.
A. Unscrew Cap
B. Insert Bare Wire C. Tighten Cap
IMPORTANT: Make sure the ( + ) and ( – ) bare wires do not touch each other or the
other terminal. Touching wires can cause a short circuit that can damage the receiver.
Connect the left and right speakers with
supplied bases:
Remove the speaker’s base (see Shelf Placement, on 1. page 12).
Pass the speaker wire through the opening in the speaker base.2.
Connect the speaker wire as described 3. above.
Reattach the speaker’s base as shown in the illustration.4.
Slide Base Straight
onto Speaker Rails
5.
- HS 280 / HS 210 1
- Table of Contents 2
- Important Safety Instructions 3
- Introduction 4
- Receiver Front-Panel Controls 6
- Receiver Information Display 7
- MODEL: HS 2X0SO/230 8
- 3/ 9
- Remote Control Functions 10
- Placing the Speakers 12
- Connections 14
- Right SatelliteLeft Satellite 15
- Subwoofer 15
- Receiver 15
- Connecting the FM Antenna 16
- Preparing the Remote Control 17
- Setting up the Receiver 18
- Settings Menu 19
- Network Settings 20
- Preferences 20
- Activity Menu 21
- Bookmarks 21
- Using the DVD Player 21
- Play Disc 22
- Using the FM Tuner 23
- Radio Station Options 24
- Viewing Pictures 25
- Playing Music 25
- Playing Videos 25
- Sharing Files 25
- Troubleshooting 27
- DVD Language Code List 28
- Specifications 29
Related products and manuals for Home cinema systems Harman/Kardon HS210
(34 pages)Sony SSSP40FWB manuals
Owner’s manuals and user’s guides for Loudspeakers Sony SSSP40FWB.
We providing 1 pdf manuals Sony SSSP40FWB for download free by document types: Datasheet
Comments to this Manuals