Harman Kardon DMC 1000 User Manual download pdf (Page 15)

REAR-PANEL CONNECTIONS

HDMI Output: Connect this output to an HDMI input on an HDMI-

compatible A /V receiver or video display device. If your A /V receiver or

surround processor is capable of decoding audio (typically, these are

HDMI “repeater” products with HDMI Version 1.1 or higher), no further

audio connection is needed for the main room (Zone 1).

NOTE: If your A/V receiver or video display uses DVI connections,

use an optional HDMI-to-DVI adapter or cable, and make a

separate digital or analog audio connection. If your DVI-equipped

display is not HDCP-compliant, the digital video connection will

not work, and you must use an analog video connection.

Composite and S-Video Outputs: If your video display does not have

HDMI or component video inputs, connect one of these two video outputs

(but not both) to your A /V receiver/processor or directly to the display.

An S-video connection, if available, is preferred. You may connect both

the HDMI Output and the Composite Video Output to the receiver if it

distributes composite video through a multiroom system.

Component Video Outputs: If your A/V receiver, surround processor

or video display is not equipped for HDMI or DVI, connect these jacks

to the corresponding inputs on the receiver or TV labeled “Y/Pr/Pb”

or “Y/Cr/Cb.” If your video display has component input jacks marked

“High Definition,” use those jacks. Do not connect the Component Video

Output jacks to standard composite video inputs on any device.

Coaxial and Optical Digital Audio Outputs: If your A/V receiver or

surround processor is not capable of processing the audio from an

HDMI stream, connect either of these digital audio outputs (but not

both) to the corresponding input on the receiver/processor. Even though

the Coaxial Digital Output uses the same RCA-type connector as stan-

dard analog audio connections, DO NOT connect it to a conventional

analog input jack.

Zone 1 Analog Audio Outputs: If you are not using either HDMI or

a separate optical or coaxial digital audio connection for the Zone 1

(Main Room) audio, connect these jacks to the matching inputs on your

A/V receiver or surround processor. Connect the left- and right-channel

jacks to the receiver to monitor an analog source connected to the

Auxiliary Inputs during recording.

Zone 2/3/4 Analog Audio Outputs: When the DMC 1000 is being

used for multizone operation, connect these jacks to the separate

Zone inputs on your multiroom controller or hub, or the amplifiers feeding

the multizone system.

The Bridge Connection: To use an iPod* as a source for the DMC 1000,

enabling you to select and listen to audio content and charge the iPod,

connect an optional Harman Kardon The Bridge here.

For iPod models with a dock connector.

USB Port: This USB port is primarily intended to connect an optional,

external USB hard drive to back up the DMC 1000’s Media Library,

although it may be used for content playback. DO NOT connect a

computer or other host device directly to the DMC 1000.

Auxiliary Inputs: Connect the “Tape Outputs” of an A/ V or stereo

receiver or a surround processor, or the line-level outputs of any audio

product, such as a phono preamp or tape/cassette deck, to transfer

content to the DMC 1000.

Network Jack: Connect this standard RJ45 jack to a broadband

network (Ethernet) connection so that you may take full advantage of

Gracenote MusicID, including obtaining cover art for stored albums,

updating both the database of album information and the system

software, and connecting the DMC 1000 to a home network. When

the network connection is “live,” the lights on either side of the jack

will flash to indicate network activity.

NOTE: When the DMC 1000 is used with an IP-based or wire-

less control device, connect a router/access point here, making

certain that one connection runs from the router to a broadband

Internet connection. When the DMC 1000 is not connected to the

Internet, Gracenote MusicID retrieves all of the tag information

other than the cover art from a database stored on the DMC 1000’s

hard-disc drive.

Remote Infrared (IR) Input and Output: When the front-panel Remote IR

sensor is blocked, connect the IR Output of your receiver/processor or

an optional IR receiver to the Remote IR Input jack. The Remote IR Output

may be connected to the Remote IR Input of a compatible source

device (or other product) for remote control through the DMC 1000.

When several devices are used, connect them in “daisy chain” fashion.

RS-232 Port: Connect the DMC 1000 to compatible system control

and automation products, using a standard RS-232 cable. As program-

ming a control and automation system is a complex task, requiring spe-

cific information and training, we recommend that you consult a trained

installer.

Master Power Switch: Push this switch to the line position (I) to apply

power to the DMC 1000, placing it in the “Full-Off” power mode described

in Table 1. When the unit will not be used for an extended period of

time, or whenever it is necessary to remove the unit from the AC power

lines, push the switch to the circle position (

) to turn the unit off.

AC Power Input: Connect the AC power cord supplied with the

DMC 1000 to this socket first, and then to an unswitched AC outlet.

Should the cord become damaged, contact your authorized

Harman Kardon dealer for a replacement.

Fan Vent: This area contains vents used by the DMC 1000’s fans to

cool the system. Maintain a clearance of at least three inches to the

nearest surface, to avoid overheating the unit.

DMC1000om.qxd 11/30/07 3:59 PM Page 15

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 47 48

Comments to this Manuals

No comments

Harman Kardon DMC 1000 User Manual Page 15

Comments to this Manuals

Related products and manuals for DVD players Harman Kardon DMC 1000