Harman-kardon HS 500 User Manual download pdf (Page 30)

INITIAL SETUP

Use the ‹/› Buttons to move the cursor to the submenu icons on the

left side of the screen, and then use the

⁄/¤ buttons to highlight the

Audio Adjustments icon, which has a picture of a set of slide switches

on it. See Figure 43. Press the Enter Button, and then use the

Navigation Buttons to move the cursor to the settings on the Audio

Adjustments submenu.

Figure 43 – Audio Adjustments

Submenu

DELAY SETTINGS: The delay settings indicate the distance from each

speaker to the listening position. Although ideally you placed all of your

speakers in a circle equidistant from the listening position, we recognize

that it isn’t always practical to do so. This setting enables the HS 500 to

delay the signal from some speakers by up to 16 mS to compensate.

You will notice that the delay settings are set in tandem for the front left

and right speaker pair, and for the surround left and right speaker pair.

Changing the settings for either speaker in these pairs also affects that

setting for the other speaker in that pair. For this reason, it is important

to place both speakers in each pair at about the same distance from the

listening position.

Use the Navigation buttons to highlight the distance for each speaker,

and press the Enter button to change it. Use the

‹/› Buttons to scroll

through the available settings.

NOTE: There is no delay setting for the subwoofer. Low-

frequency sound waves by their nature are not noticeably

affected by the distances in a typical listening room.

OUTPUT LEVEL SETTINGS: Output level adjustment is a key part of

the configuration process for any surround sound system. The goal is to

set the output levels so that all channels sound equally loud at the listening

position. This is important because movie directors adjust the loudness

of each channel in the recording to produce a desired sound presentation.

Usually the director reduces the loudness, or even the presence, of

information in the surround channels so as not to distract the viewer

from the main action taking place on screen. If the test tones on your

test disc sound as loud in the rear speakers as they do coming from

the other speakers, the HS 500 is performing correctly.

In many cases the factory default setting of 0dB should accomplish that.

However, in some cases the specifics of your listening room may require

some adjustments.

To adjust the output levels, first insert a disc with test tones or content

you are familiar with, and that has a reasonably even level without many

dynamic changes.

If you are using an SPL meter with a disc containing test tones, adjust

the level of each channel so that the meter reads 75dB. If you don’t

have a meter or a test disc, adjust the levels until all channels sound

equally loud. Make sure not to use a surround sound-encoded disc for

this process, or the surround channels will be set too high.

Use the Navigation Buttons to highlight the level setting for the front left

channel. Press the Enter Button to display the available settings, which

range from –6 dB to +6dB, and use the

‹/› Buttons to scroll through

them until you are satisfied with the level setting for that channel. Press

the Enter button to select the setting, and use the Navigation Buttons to

select the next channel. Repeat the procedure to enter the output level

offset, if needed, that brings all of the channels to the same output

volume. You may need to repeat this procedure more than once to

accurately set the levels.

Step Four – Video Setup

In this step you will make a few adjustments to ensure that the video

signal is output in a way that is compatible with your video display.

Use the

‹/› Buttons to move the cursor to the submenu icons on the

left side of the screen, and then use the

⁄/¤ buttons to highlight the

Video Setup icon that has a picture of a gear on it. See Figure 44.

Press the Enter Button, and then use the Navigation Buttons to move

the cursor to the settings on the Video Setup submenu.

Figure 44 – Video Setup Submenu

ASPECT RATIO: This setting selects the aspect ratio of video program-

ming. Your choice should be made according to the shape of your video

display and your personal preferences. Three choices are available:

• 16:9: If you have a widescreen (16:9) display, or a display that has

a widescreen mode, choose this setting. The HS 500 will adjust the

output for widescreen movies so that they fill the entire screen in the

proper aspect ratio. However, a disc recorded in the 4:3 aspect ratio

will appear as a boxed image in the center, with black or gray bars on

the left and right side of the screen. If the widescreen option is chosen

and a widescreen movie is played on a conventional 4:3 aspect ratio

set, the image will be distorted due to vertical compression.

• 4:3 Letterbox: If you have a standard, 4:3 aspect ratio video display,

choose this setting to see the entire frame of the movie as it is

recorded on the disc without any image cutoff at the left and right

sides. While this allows widescreen movies to be shown in their entirety,

they will occupy a smaller portion of the screen and black “letterbox”

bars may appear at the top and bottom of the screen.

1 2 ... 25 26 27 28 29 30 31 32 33 34 35 ... 71 72

Comments to this Manuals

No comments

Harman-kardon HS 500 User Manual Page 30

Comments to this Manuals

Related products and manuals for Home Theater Systems Harman-kardon HS 500