Harman/Kardon HK 990 Owner's Manual download pdf (Page 7)

ENGLISH

Remote Control

REMOTE CONTROL

Independent Remote Control

The system remote of the HK 990 can control

the amplifier and compatible Tuners, CD Players

and CD Recorders. The remote In jack of units

without an integrated IR receiver must be con-

nected to the amplifier's remote control output

jack so that the system remote control can oper-

ate them.

Important Notes:

To remote control a tuner, CD Recorder or •

CD Player, the appropriate input (”TUNER”,

”CDR” or ”CD”) must have been selected

with the source buttons of the remote

control (selecting on the front panel is not

sufficient).

Note that DVD players cannot be controlled •

by the remote.

Operating Conditions

The control unit operates effectively within a

distance of 7 meters and an angle of 30° from

the amplifier. Using the control near fluorescent

lights may shorten this range, as will any dust

or dirt that accumulates on the front of the

remote control or the remote sensor area of the

amplifier. Also avoid blocking the line of sight

between amplifier and remote.

Install the four supplied AAA batteries in the

remote as shown. Be certain to follow the (+)

and (–) polarity indicators that are on the top of

the battery compartment.

When you replace weak batteries, replace all at

the same time. When the remote is to be unused

for an extended period, remove the batteries to

prevent damage from corrosion.

Instructions for

users on removal

and disposal of

used batteries.

Specification of included battery types.

These symbols shown on the product, the pack-

aging or in the manual or separate information

sheet mean that the product itself, as well as

the batteries included or built into the product,

should never be thrown away with general

household waste. Take them to applicable col-

lection points, where proper treatment, recycling

and recovery takes place, in accordance with

national or local legislation, or European Direc-

tives 2002/96/EC and 2006/66/EC.

Correct handling of the product and batteries to

be disposed helps saving resources and prevents

possible negative effects on the environment or

human health.

The batteries included with your equipment may

be Alkaline, Carbon Zink/Manganese or Lithium

(button cells) type. All types should be disposed

of according to the above instructions.

To remove the batteries from your equipment or

remote control, reverse the procedure described

for inserting batteries in the Owners Manual.

For products with a built-in battery that lasts for

the lifetime of the product, removal may not be

possible for the user. In this case, recycling or

recovery centers handle the dismantling of the

product and the removal of the battery. If, for

any reason, it becomes necessary to replace such

a battery, this procedure must be performed by

authorized service centers.

HK 990 Remote Control functions

(Please refer to the illustration of the Remote

Control on the next page).

Device ON/OFF: These two Buttons switch ON

and OFF a (Harman Kardon) device selected with

the MODE Button or selected by pressing its Sys-

tem On source Button (in both cases, the System

ON Device Button lights up).

System OFF: Switches the entire system off.

(The HK 990 and other Harman Kardon products

that have a Remote Sensor or are connected to

the Remote Jacks on the HK 990 back panel).

System ON: This group of 9 Buttons switches

the HK 990 ON, as well as the (Harman Kardon)

device written on the Button that you press

(AMP, CD, TUNER, CD Recorder, TAPE). Also

switches the remote’s frequencies to control the

device indicated on the active Button and selects

this device to be Input on the HK 990. Please

note that while a number of remote functions

are switched to control the device selected,

some of the amplifier’s main functions always

remain active, such as Volume. Please refer to

the Remote Control Function List for information

on which functions can be remote controlled for

each type of device and which buttons always

control the HK 990.

MODE: Scrolls through the nine System On But-

tons, each Button lighting up in turn. This feature

allows you to control the device you select,

without changing the Input of the HK 990. Note

that a number of Remote Functions are always

active for the HK 990 no matter which device

you select with the Mode Button. Refer to the

Remote Control Function List.

Info/RDS: Selects information for a CD player,

such as CD-Text if available on the CD. Selects

RDS function for a tuner.

Time: Selects time information for a CD player

or a CD recorder.

Display: Switches the display brightness of

the HK 990 and other HK units in steps of Full

brightness, Reduced brightness and Display Off.

Numeric Buttons (0-9): Used to enter track

numbers on CD or CDR units or to enter preset

numbers/frequency digits on a Tuner. You may

begin play of a CD with the Numeric Buttons by

entering the digits of the track directly. Press “5”

to initiate play from track 5. Press “1” immedi-

ately followed by “4” to initiate play from track

14 and “2” immediately followed by “7” to initi-

ate play from track 27.

1 2 3 4 5 6 7 8 9 10 11 12 13 14

Comments to this Manuals

No comments

Harman/Kardon HK 990 Owner's Manual Page 7

Comments to this Manuals